1EUpdate guide
5 Sequencer Sequencer mode About the HD Audio Track function TRITON STUDIO System Version 2.0 adds two audio tracks to the sixteen MIDI tracks and ma
6 About the audio tracks The audio tracks used by a song (Audio Track 1, 2) are a single stereo WAVE file that is created by recording in synchronizat
7Sequencer5 You use the “Erase Measure” command to erase measures 1 through 4 of audio tracks 1 and 2. This actually overwrites “zero” level sample da
8Recording an audio track1. Preparing to record an audio trackThe audio track data that you record is saved on the internal hard drive as a WAVE file.B
9Sequencer6 Be sure that “WAVE File” reads No Assign. If a file name is displayed for “WAVE File,” then a WAVE file is already assigned to the audio tra
10Then set the “BUS Select” that follows the insert effect you are using to 1/2.A In the Sequencer P0: Play/REC, Preference page, set “Track Select” t
11SequencerWhen you record or play back a song that contains audio tracks, there will be a lag of several seconds from the time you press the SEQUENCE
12If “Overwrite.WAV” is checked, you won’t have to wait as long for the internal processing to be completed when recording begins and ends, but you wi
13Sequencer3 Press the SEQUENCER [START/STOP] key to play back the song, and adjust the output level balance of audio tracks 1 and 2.Use AUDIO 1 “Leve
14In some cases (such as the hard disk being subjected to physical shock), data saved on the hard drive may become unreadable. We recommend that impor
i Table of Contents About this manual...iii Introduction... 1 New function
15Sequencer0–7: Sampling/HD AudioThe 0–7: Sampling page has changed to the 0–7: Sampling/HD Audio page (the tab has changed from Sampling to Sampling/
160–7: Page Menu CommandIn the 0–7: Sampling page, the page menu commands “Sel Dir/WAVE (Audio Track),” “Auto Sampling/HD Audio Setup,” “Bounce All Tr
17Sequencer4 Press the Set button to assign the selected WAVE file to the audio track.Only a 48 kHz stereo WAVE file can be assigned to the audio track.
182 Use “To Song” to select the bounce-recording destination song.3 Use “WAVE” to specify a name for the WAVE file that will be created by the bounce-r
19SequencerIndiv.1/2: Signals sent to the INDIVIDUAL 1, 2, or 1/2 buses will be recorded.Any signals being sent to the INDIVIDUAL 1, 2, or 1/2 buses,
20Sequencer P5: Track EditAudio tracks can now be edited in the Sequencer P5: Track Edit page (☞PG p.68). Accordingly, an audio track display has been
21SequencerIf you select a WAVE file that is other than 44.1 kHz or 48 kHz, an error message of “Can’t Put” will appear.You cannot “put” a WAVE file tha
224 Use “Sensitivity” to set the sensitivity at which noise will be detected.Higher settings will cause even slight noises to be detected. Normally yo
23SequencerTo hear the sound of the specified region, press the SAMPLING [START/STOP] key. The region specified by “Start” and “End” will play back when
24Changes to the page menu commandsSupport for audio tracks has been added to the following page menu commands, and the dialog boxes have changed acco
ii Loading KARMA Music Workstation or TRITON Le .PCG/.SNG files...54 Parameters that are valid on the KAR
25SequencerThe way in which the Compare function operates will depend on this setting. (☞p.44)5 Press the OK button to execute the command. In the cas
265–1J: Copy Measure5–1K: Move MeasureThe items “All MIDI Tracks,” “Overwrite.WAV,” and “Name” have been added to the dialog box of “Copy Mea-sure” an
27Sequencer5–1Q: Set Song LengthThe items “Overwrite.WAV” and “Name” have been added to the page menu command “Set Song Length” (☞PG p.75). If the son
28The page menu command “Auto Sampling/HD Audio Setup” has been added to the Sequencer P0: Play/REC, Sampling/HD Audio page. (☞p.17)This convenient fu
29SequencerIf “Convert to Program” is not checked, you can listen to the sample by selecting and playing it in Sampling mode.3. In-Track SamplingThe I
304. 2ch Mix to DiskAs a preparatory step to creating an audio CD from your completed song, you must resample your song to create a two-channel stereo
31Sequencer Recording on the audio track(s)7 Set “Location” to the location that you want to record.8 Press the SEQUENCER [REC/WRITE] key and then the
32Automatically-set parameters and their values-: Not set automaticallySettings enclosed in parentheses ( ) are set automatically according to the pa
33Sequencer-: Not set automaticallySettings enclosed in parentheses ( ) are set automatically according to the parameters in the dialog box.*1: The s
34Recording and playing exclusive eventsVersion 2.0 allows exclusive messages to be recorded and played back, and allows you to edit tracks that conta
iii How this manual is organized This manual explains the new features and functions that have been added in the TRITON Studio operating system versi
35Sequencer2. Recording exclusive messages received from the TRITON-RackHere’s how you can connect the TRITON STUDIO and a TRITON-Rack via MIDI, and u
36The maximum amount of exclusive message that can be recorded at once is approximately 320 Kbytes. This size will decrease if other events exist with
37Sequencer3. Put Effect Setting to TrackThe page menu command “Put Effect Setting to Track” places effect settings into a track as exclusive events.A
382) Using the effect specified by the song itself from the beginning of the song, and inserting the effect settings from another song at the middle of
39SequencerSequencer P5: Track EditThe Sequencer P5: Track Edit page menu commands “Event Edit” (☞PG p.69) and “Erase Measure” (☞PG p.70) now allow yo
40Sequencer P8: Insert EffectThe “Put Effect Setting to Track” page menu command has been added to Sequencer P8: Insert Effect.Added page menu command
41SequencerTone Adjust pages have been added to Sequencer P5: Track Edit (☞PG p.68).5–3: Tone1.2 1–8 (Tone1/2 T01–08)5–4: Tone1.2 9–16 (Tone1/2 T09–16
42Filtr EG A (Filter EG Attack) [–99...+00...+99]Filtr EG D (Filter EG Decay) [–99...+00...+99]Filtr EG S (Filter EG Sustain) [–99...+00...+99]Filtr E
43Sequencer“Copy From Program” has been added to the page menu commands of the Sequencer P0: Play/REC page and related pages.0–1L: Copy From ProgramCo
44This function automatically sets up a song by applying the settings from a program or combination. This provides a seamless way for you to transitio
45DiskGlobalSamplingCombinationProgramOther functionalityDisk modeThe 0–6: Edit WAVE page has been added to Disk mode.Here you can edit WAVE files that
46address will move by one pixel.) In the vertical axis, you can zoom-in through a range of 1x (full range display) to 512x (in the case of stereo, 10
47DiskGlobalSamplingCombinationProgramOther functionality0–6D: ClearThis command sets all data to zero in the “Edit Range Start” – “Edit Range End” re
48time signature, “Tempo” specifies the destination tempo, and “Program” specifies the program number that will be automatically created.0–6O: Mono to S
49DiskGlobalSamplingCombinationProgramOther functionality29) Load AKAI Volume: This command loads the Program files and Sample files from a volume of an
50.KSC files with a name identical to the .PCG file will always be loaded together with the .PCG file. If this file is not found in the current directory
51DiskGlobalSamplingCombinationProgramOther functionalityIn the 0–2: Save page menu command “Save to Std MIDI File (Save Song as Standard MIDI File),”
52“Collect Audio Track file” has been added to the 0–3: Utility page menu commands.0–3K: Collect Audio Track fileThis command copies/moves the WAVE file
53DiskGlobalSamplingCombinationProgramOther functionality4 Select the page menu command “Collect Audio Track file” to open the dialog box.5 Press the C
54A function that converts a 44.1 kHz WAVE file to a 48 kHz WAVE file has been added to the 0–3: Utility page menu command “Rate Convert” (0–3H ☞PG p.17
Introduction1 Introduction Sequencer mode 1. HD Audio Track function ( ☞ p.5) Two audio tracks (1 and 2) have been added to the existing sixteen MIDI
55DiskGlobalSamplingCombinationProgramOther functionality3. Sequencer mode parameters• The KARMA system version 2.0 “Tone Adjust” setting will be load
56Global mode“SCSI Mode” and “SCSI ID” parameters have been added to the Global P0: Basic Setup, System Preference page (☞PG p.137). These parameters
57DiskGlobalSamplingCombinationProgramOther functionality3 In the Global P0: Basic Setup, System Preference page, set “SCSI Mode” to Target.A dialog b
58Sampling modeAn “Auto Sampling Setup” page menu command has been added to the Sampling P0: Recording page and P4: Selector Setup page.0–1O: Auto Sam
59DiskGlobalSamplingCombinationProgramOther functionalityIf “Save to” is set to DISK, you can use the page menu command “Select Directory” (0–1N ☞PG p
60Automatically-set parameters and their values- : Not set automaticallyValues enclosed in parentheses ( ) are automatically set according to the set
61DiskGlobalSamplingCombinationProgramOther functionalityYou can now use the “Insert,” “Mix,” and “Paste” page menu commands of the Sampling P1: Sampl
62If the insert-source is a stereo WAVE file, use “Save to No. (L)” and “(R)” to specify the save-destinations of the L and R channels.C Press the OK b
63DiskGlobalSamplingCombinationProgramOther functionalityCombination modeAn “Auto Sampling Setup” page menu command has been added to the Combination
64 Check the resampled data• If you selected “Save to: RAM” (Convert to Program), move to Program mode, select the newly created program, and play the
2 Disk mode 1. “Advanced Conversion Load” for loading AKAI Programs ( ☞ p.48) In addition to previously supported keymap-related param-eters, version
65DiskGlobalSamplingCombinationProgramOther functionalityAutomatically-set parameters and their values- : Not set automaticallyValues enclosed in pare
66“Copy From Program” has been added to the page menu commands of pages such as Combination P0 (0–1 ☞PG p.33).0–1C: Copy From ProgramThis command copi
67DiskGlobalSamplingCombinationProgramOther functionalityProgram modeAn “Auto Sampling Setup” page menu command has been added to the Program P0: Samp
68 Check the resampled data• If you selected “Save to: RAM” (Convert to Program), select the newly created program, and play the C2 note of the keyboa
69DiskGlobalSamplingCombinationProgramOther functionalityAutomatically-set parameters and their values- : Not set automaticallyValues enclosed in pare
70Other functionalityA tap tempo control function has been added to Program, Combination, Sequencer, and Song Play modes.While SMF data is playing in
71DiskGlobalSamplingCombinationProgramOther functionalityAdded messagesThe following messages have been added.Audio Track size over limitCan’t record
KORG INC.15 - 12, Shimotakaido 1 - chome, Suginami-ku, Tokyo, Japan. 2003 KORG INC. 1505 CGH Printed in Japan1E
3 Introduction You can update your TRITON STUDIO system to Version 2.0 via the internal floppy drive, by loading TRITON STU-DIO Version 2.0 operating
Kommentare zu diesen Handbüchern