Korg Triton Studio Bedienungsanleitung PDF herunterladen (Seite 190)

179

Effect

2. Routing

You can use up to ﬁve channels (IFX 1, 2, 3, 4, and 5) for the

Insert Effects in any mode.

2–1. Program mode

Use “BUS Select” (Program P8: 8–1c) to set the destination

bus of the oscillator output.

L/R: The signal is not sent to the Insert Effects. Instead, it is

sent to AUDIO OUTPUT (MAIN) L/MONO and R after the

Master EQ.

IFX1–5: The signal is sent to Insert Effects IFX 1, 2, 3, 4, 5.

1, 2, 3, 4, 1/2, 3/4: The signal is sent to AUDIO OUTPUT

(INDIVIDUAL) 1, 2, 3, 4 (“Individual Outputs” ☞p.185).

The signal is not sent to the Insert Effects, Master Effects,

and or Master EQ.

Off: The signal is not sent to the L/R bus, 1, 2, 3, or 4 busses.

After the Master Effects, the signal is output to AUDIO

OUTPUT (MAIN). Select this option if you connect the

Insert Effects with the Master Effects in series, with the send

level speciﬁed by “Send1 (MFX1)” and “Send2 (MFX2).”

Use “Send1 (to MFX1)” and “Send2 (to MFX2)” (Program

P8: 8–1d) to specify the send level for the Master Effects.

This setting is effective if “BUS Select” is set to L/R or Off.

If “BUS Select” (Program P8: 8–1c) is set to IFX1–5, use

“Send1” and “Send2” (Program P8: 8–2a) to specify the send

level of the post-IFX signal (☞“3. Mixer”).

Send1 responds to CC#93, and Send2 responds to

CC#91. At this time, the actual send level uses the value

of the Send 1 and 2 settings for Oscillators 1 and 2, mul-

tiplied by the Send 1 and 2 values received via MIDI.

If you are connecting the Insert Effects in series, check the

“Chain” box (Program P8: 8–2a). If you check the box that is

located between IFX1 and IFX2, the output signal from IFX1

is sent to IFX2. When the Insert Effects are connected in

series, the values of the “Pan (CC#8),” “BUS Select,”

“Send1,” and “Send2” parameters for the post-IFX signal

will be used (☞“3. Mixer”).

The following ﬁgure shows an example of Oscillators 1 and

2 outputs being sent to IFX1.

Check the “Chain” box to connect IFX1, 2, 3, 4, and 5 in

series in this order. The “Pan (CC#8),” “BUS Select,”

“Send1,” and “Send2” parameters for the post-IFX5 signal

will be used.

— Settings for drum programs —

If you have selected “Drums” for “Oscillator Mode” (Pro-

gram P1: 1–1a) of a Program, the “USE DKit Setting” box

(Program P8: 8–1b) becomes available. If you check this box,

“BUS Select” (Global P5: 5–2b) for each key of the selected

DrumKit becomes effective.

For example, you can send a snare sound to IFX1 to apply

the Gate effect, a kick sound to IFX2 to apply EQ, and other

sounds to AUDIO OUTPUT (MAIN) L/MONO and R with-

out applying any Insert Effects. If you de-select the box, all

drum instrument outputs are sent to the bus speciﬁed by

“BUS Select” (Program P8: 8–1c). You may apply any Insert

Effects to all drum instruments, regardless of the DrumKit

settings.

2–2. Combination, Sequencer, and Song Play

modes

Use “BUS Select” (P8: “Routing” page in each mode) for

timbres (Combination) and tracks (Sequencer, Song Play) to

select an Insert Effect to apply to the corresponding timbres

and tracks. You can route multiple timbres and tracks to a

single Insert Effect.

As with Program mode, select L/R, IFX1–5, 1–4, 1/2, 3/4, or

Off for each timbre and track.

“Send1 (MFX1)” and “Send2 (MFX2)” become available if

“BUS Select” has been set to L/R or Off.

If IFX1–5 is selected, use “Send1” and “Send2” for the post-

IFX signal (☞“3. Mixer”).

Send1 responds to CC#93, and Send2 responds to

CC#91. At this time, the actual send level uses the value

of the Send 1 and 2 settings for Oscillators 1 and 2 of the

Programs (selected for the timbres and tracks), multi-

plied by the Send 1 and 2 values received via MIDI

(“Send Level” ☞p.183).

The following ﬁgure shows an example of Combination

mode. The Timbre 1 output is sent to IFX1 and the Timbre 2

output is sent to IFX2 according to the “BUS Select” setting.

Other timbres are sent to L/R. The output signal passes

through the Master EQ, then goes to AUDIO OUTPUT

(MAIN) L/MONO and R.

In the following example, the “Chain” box between IFX1

and IFX2 is checked so that the IFX1 output is sent to IFX2.

“IFX1: 001: St. Amp Simulation” and “IFX2: 020: Stereo

Flanger” are inserted to Timbre 1. “IFX2: 020: Stereo

Flanger” is inserted to Timbre 2. The ﬁgure above (“Rout-

ing” pages) shows these settings. (In this example, IFX 3, 4,

and 5 are not being used.)

1 2 ... 185 186 187 188 189 190 191 192 193 194 195 ... 321 322

Kommentare zu diesen Handbüchern

Keine Kommentare

Korg Triton Studio Bedienungsanleitung Seite 190

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Die Eingabegeräte Korg Triton Studio