Korg Triton Studio Bedienungsanleitung PDF herunterladen (Seite 244)

Effect

233

093: Vocoder

This effect applies the character of the right channel signal

(Modulator) to the left channel signal input (Carrier). A com-

mon use of this effect is to produce the sound of various

instruments by inputting a voice to the Modulator via a

microphone. A special effect is also achieved by using rhythm

or effect sounds. Strings or distortion guitar sounds with a lot

of harmonics are suitable as a Carrier.

c: Formant Shift

By offsetting the Carrier ﬁlter, you can adjust the height of the fre-

quency range to which the vocoder effect is applied. The tonal

quality will change signiﬁcantly.

e: Noise Level

This parameter enables you to mix white noise with the Carrier.

f: Modulator High Mix

This parameter sets the high-range output level of the right chan-

nel sound (Modulator). If the modulator is a human voice, it will

make the words more clear.

h: Vocoder/Carrier, i: Wet/Dry

The “Vocoder/Carrier” parameter sets the balance between the

vocoder sound and the left channel sound (Carrier). The “Wet/

Dry” parameter sets the balance between the effect and dry

sound.

If you wish to change the intensity of the vocoder effect, select

Wet for “Wet/Dry”, and adjust the balance using the “Vocoder/

Carrier” parameter.

Using a voice from a microphone as a modulator

(Vocoder is selected for IFX2 in Program mode)

1 Set “Pan” (Program P4: 4–1b) to L001 for Amp1 Level/Pan so

that the Carrier sound will be input only to the left channel.

When Oscillator Mode (Program P1: 1–1a) is set to Double, set

Pan for Amp2 Level/Pan to L001.

2 To set up the input, use the “Audio Input” parameter (Global

P0: 0–3a).

Connect a microphone to AUDIO INPUT1 or INPUT 2 connec-

tor, and set the [LEVEL] switch to MIC.

While talking into the microphone, adjust the [LEVEL] knob

so that the level is high enough, but the sound will not be dis-

torted.

For the Audio Input parameters for the microphone, set Pan to

R127 and BUS (IFX/Indiv.) Select to IFX2.

Now the voice from the microphone is input to the modulator

channel. You can create the sound of a “talking” instrument

when you talk into the microphone while playing.

Wah Sweep Range –10...+10

Sets the range of Wah

☞ Fx:006,

Wah Sweep Src Off...Tempo

Selects the modulation source that controls the Wah

Drive Mode Overdrive, Hyper-Gain

Switching between overdrive and hyper-gain mode

Drive

Sets the degree of distortion

1...120

☞ Fx:006

Pre Low-cut 0...10

Sets the low range cut amount of the distortion input

☞ Fx:006

Output Level 0...50

Sets the output level

☞ Fx:006,

Src

Selects the modulation source for the output

level

Off...Tempo

Amt

Sets the modulation amount of the output level

–50...+50

Low Cutoff [Hz] 20...1.00kHz

Sets the center frequency for Low EQ (shelving type)

Gain [dB]

Sets the gain of Low EQ

–18...+18dB

Mid1 Cutoff [Hz] 300...10.00kHz

Sets the center frequency for Mid/High EQ 1 (peaking type)

Sets the band width of Mid/High EQ 1

0.5...10.0

☞ Fx:006

Gain [dB]

Sets the gain of Mid/High EQ 1

–18...+18dB

Mid2 Cutoff [Hz] 500...20.00kHz

Sets the center frequency for Mid/High EQ 2 (peaking type)

Sets the band width of Mid/High EQ 2

0.5...10.0

☞ Fx:006

Gain [dB]

Sets the gain of Mid/High EQ 2

–18...+18dB

Direct Mix

Amount of the dry sound mixed to the distortion

0...50

Speaker Simulation

Speaker simulation on/off

Off, On

Wet/Dry Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

Src Off...Tempo

Selects the modulation source of the effect balance

Amt

Sets the modulation amount of the effect balance

–100...+100

L (Carrier) Trim

Sets the input level of left channel (Carrier)

0...100

R (Modulator) Trim

Sets the input level of right channel (Modulator)

0...100

Left

Right

Wet / Dry

Wet: Stereo In - Mono Out / Dry: Stereo In - Stereo Out

Band Pass Filter

Envelope

Modulator

Carrier

Lch (Carrier)

Trim

Rch (Modulator)

Trim

Modulator High Mix

Vocoder /

Carrier

Noise

Generator

Noise Level

Formant Shift –2...+2

Sets the height of the frequency for the vocoder effect

☞

Response 0...100

Sets the speed of the response to the modulator input

Noise Level

Sets the noise mix level to the Carrier

0...100

☞,

Src Off...Tempo

Selects the modulation source for the noise mix level

Amt –100...+100

Sets the modulation amount for the noise mix level

Modulator High Mix

Sets the high-range output level of the modulator

0...100

☞

Low Gain [dB]

Sets the low-range output level of the vocoder

–12...+12

High Gain [dB]

Sets the high-range output level of the vocoder

–12...+12

Vocoder/Carrier Carrier, 1:99...99:1, Vocoder

Sets the balance between the vocoder output and the Carrier

☞,

Src Off...Tempo

Selects the modulation source for the balance between the vocoder

output and the carrier

Amt –100...+100

Sets the modulation amount of the balance between the vocoder out-

put and the carrier

Wet/Dry Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

☞,

Src Off...Tempo

Selects the modulation source of the effect balance

Amt

Sets the modulation amount of the effect balance

–100...+100

1 2 ... 239 240 241 242 243 244 245 246 247 248 249 ... 321 322

Kommentare zu diesen Handbüchern

Keine Kommentare

Korg Triton Studio Bedienungsanleitung Seite 244

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Die Eingabegeräte Korg Triton Studio